car battery replacement dubai
car battery replacement Sharjah

How to care for your car battery

Summer Car Maintenance In UAE
April 7, 2019
Car Flat Tyre Replacement Dubai
Rapid Emergency Flat Tyre Change Services in Dubai at Dial4Battery
April 7, 2019

Avoid an expensive service or tow charge (and the worry of being stranded!) by keeping your car battery working at peak performance. This article will show you how to perform a simple step-by-step 10-minute seasonal battery check-up so you know whether your battery is performing well. This article will also explain how to replace your battery if it’s failing, so you’re not left stranded out in the middle of nowhere with a car that won’t start.

The last thing you need is a car that won’t start because the battery is dead. You can avoid that expensive service or tow charge (and the worry of being stranded!) by carrying out a 10-minute seasonal battery check along with a few maintenance tips. In addition to a set of wrenches, you’ll only need a post cleaner or side terminal, a hydrometer and a cable puller, all available at auto parts stores. Keep in mind that you can skip the battery service if you make sure the mechanic does it during periodic servicing, but you’ll want to keep up with the regular maintenance.

Step 1: Clean the cables

Clean corrosion from the battery

Clean corrosion from the top of the auto battery first and then clean corrosion from around the battery cables with a post cleaner.

First clean the top of the battery and any corrosion from the cables using a tablespoon of baking soda, a cup of water and a nonmetallic brush. Flush with cool water. Now disconnect the cables, starting with the negative one to prevent your wrenches from arcing on a nearby ground. Loosen the battery cable clamp bolts and gently give them a twist. Use a cable puller if they’re stuck. Never pry on the auto battery posts. If you have a side post terminal (not shown), use a 5/16-in. box wrench to loosen the cables. With the cables removed, further clean off the corrosion around the auto battery terminals and cables with a post cleaner.

Step 2: Check the level of the electrolyte

Add water to fill holes, if necessary

If the battery needs water, use clean, distilled water and don’t over fill the cells.

No-maintenance battery

If you have a no-maintenance battery, check to see if you have a green dot in the sight glass/charge indicator. Green means the battery is good. If it’s dark, it needs recharging. If it’s yellow or has no color at all, (inspect carefully and use a flashlight), replace the battery.

Memory saver

If you have preset radio stations or other memory functions in your car and want to keep them, go to your auto parts store and get a device like the one shown and a fresh 9-volt battery. Plug this into your cigarette lighter before you disconnect the cables. This will give you about one hour to clean the cables and test the battery charge.

Gently pry off the covers of the battery cells. (We discuss what to if you have a no-maintenance sealed battery later in this step.) The water and acid mixture in the battery (electrolyte) should be about 1/2 in. deep or to the bottom of the fill hole. If it needs water, use clean distilled water, being careful not to overfill the cells, and then inspect the battery case for cracks. If you find a crack, replace the battery. If you added water, let the water mix with the electrolyte for a few hours before the next step. (You may need to reconnect the battery to maintain your memory functions.)

Step 3: Check the condition and charge of the battery

Test the electrolyte in each cell with a hydrometer

To test the electrolyte in each cell, squeeze the ball on the hydrometer and draw the solution into the tester. Hold the test level, record the reading and squirt the solution back into the cell.

Test the electrolyte in each cell. Squeeze the ball and draw the solution into the tester. Carefully hold the tester level and write down the reading. Squirt the solution back into the same cell. The testers are calibrated assuming a battery is at 80 degrees F. Add .04 to each reading for every 10 degrees above 80 and subtract .04 for every 10 degrees below. If you get a cell reading that differs from the others by .05 or more, replace the battery. A fully charged battery should have a reading of 1.265 or higher. If all the readings show fair or low (1.200 is low) but are consistent, recharge the battery. Learn how to replace a car battery in our video tutorial.

Step 4: To drop in the new battery first remove the cables

Disconnecting negative cable first

Disconnect the negative cable first and then the positive

Remove your battery hold-down clamp. Disconnect the negative cable first, then the positive. Note: Always replace the battery with one that has a higher rating than the original.

CAUTION!

Always wear eye protection and rubber gloves when working on batteries, and never smoke around them!

Step 5: Replace the battery

Lifting out old battery

Use the heavy-duty strap to carefully lift out the old battery

Tie a heavy-duty strap to the ears on the side of the battery and gently lift it out. Be careful; battery acid is dangerous. Don’t drop it. Once the battery is out, clean the battery tray and replace it if it’s badly corroded. Batteries are heavy and need solid support!

Step 6: Reinstall the clamp and cables

Connecting hold-down clamp

Connect the hold-down clamp before connecting the cable to the terminals

Carefully lift the new battery into place. Connect the hold-down clamp, then connect the cable to the positive terminal first and the negative last (for negative ground systems). Smear a little petroleum jelly onto the terminal before fastening the cable clamps to the posts. The grease will help slow corrosion. Most batteries are at least 75 percent charged when you buy them and should be ready for you to start your car and drive. Check with your supplier to see if your new battery needs charging before you use it.